www.iogear.comUser ManualWireless 5x2 HD MatrixGWHDMS52PART NO. M1229-b
23142 31 410ReceiverTop view1. Power Button with LED indicator Press to turn the receiver On and Off. The indicator in the power button lights up in
811Remote Control1. POWER ON / POWER OFF Buttons Press Power ON to turn the Transmitter & Receiver ON. Press Power OFF to turn the Transmitter &a
IR BlasterVCRHD Cable BoxBlu-ray Player HD Gaming BoxHome PCHD Projector or HD Flat Panel TV12Hardware InstallationStep 1: Setup the TransmitterConnec
13Step 2: Setup the ReceiverHDTV Connection with receiver:1. Connect the supplied mini USB power adapter to the DC IN jack of the receiver and a wall
14Step 3: Setup the IR blaster extender cable and IR sensor extender cableThe IR relays infrared commands from your remote control to your device. Us
15Step 4: Mounting the Receiver to a Wall (Optional)1. Refer the drawing at right that has relative position of the main holes that will be needed to
16Basic Operation1. After the power adapter is plugged into the electrical outlet, the device will turn ON automatically.2. If the receiver is in St
174. During warm-up, the transmitter’s and the receiver’s wireless status LED will blink green until the signal link between the transmitter and the
Note: Pressing “Up” or “Down” on receiver side or pressing “Left” or “Right” on transmitter side will not initiate switching.OSD Displayed:18B. Remot
197. If operation is normal, the POWER/Wireless status LED and Source Status LED will glow in solid green. Please refer to the LED status table below
© 2014 IOGEAR® Part No. M1229-bIOGEAR, the IOGEAR logo, are trademarks or registered trademarks of IOGEAR. Microsoft and Windows are registered tradem
ONHDMI1 CH1 1280x1024= OFFHDMI1 CH1 1280x1024HDMI1 CH1 1280x1024= 47KHzHDMI1 CH1 1280x1024= 56KHz20E. On Screen Display (OSD) vs. Rem
21*21(1) Transmitter – Using a Mini USB to USB Type A USB cable, Plug the mini USB side into the transmitter and the USB type A into the computer you
22Advanced OperationNaming the Input Source Devices1. Press and hold the Source button on the top of transmitter for over 3 seconds. A source nami
22Wireless 5x2 HD MatrixSource23Pairing new transmitter with existing receiver (optional)Enter the Pairing mode for transmitter:1. Unplug Power Adapt
24Multiple Transmitter Selection1. Verify that the power is removed from Transmitter 1. Press Transmitter No. key on the remote control and point it
254. Enter “Remove Transmitter” menu if you would like to remove a transmitter OSD Displays:5. Enter “Modify Transmitter Name” menu if you would l
26Supported ResolutionIf the SOURCE LED continues to blink in green (slower than “no signal” mode); OSD display: , and there is no video displayed or
27If the Source/Status LED continues to blink green (slower than “no signal” mode); or OSD display shows , please check that both TVs connected to
28SpecicationsSupported Video ResolutionsHDMI Input 3D, 1080p, 1080i, 720p, 576p, 480pComponent Input 1080i, 720p, 576p, 576i, 480p, 480iSupported Au
291. Problem: The power indicator LED doesn’t light up.Solution: Check the power adapters of the Transmitter/Receiver to see if they are properly ins
3Table of ContentsImportant Information 4Introduction 8Package Contents 8Requirements 8Overview 9Hardware Installation 12Step 1: Setup the Transmitter
304. Problem: No audioSolution:• Check your TV’s volume is properly set and not set in “MUTE” mode.• Check if your source player’s audio volume has
31Federal Communications Commission (FCC) StatementTheuseriscautionedthatthisdeviceshouldbeusedonlyasspeciedwithinthismanualtomeet R
©2014 IOGEAR®
4Important InformationPlease take the time to read this user manual before using the Transmitter and Receiver. It contains important information abou
5• Never use this product nearby an aircraft or medical facility. It can cause interference or undesirable effect on the operation result• Use of t
6 CAUTION: Using the System in the US• Anychangesormodicationsnotexpressly approved by the grantee of this device could voi
7French translation:Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionne
8IntroductionIOGEAR’sGWHDMS52Wireless5x2HDMatrixisthersttosendFulluncompressedHD1080p, connects up to 5 source devices and allow you
2 312 3145 69OverviewTransmitter Top view1. Source LEDs These LED indicators are lit in solid green to show current input2. Source Selection Button
Kommentare zu diesen Handbüchern