Iogear GCL1800 Bedienungsanleitung

1GCL1800 PART NO. M1122InstallationInstallation Guide17” LCD Combo Console

Final StepAfter the rear brackets are completely secured, tighten the front brackets’ screws.Step 2While the person continue holding the position of t

To prevent damaging your equipment, it is important that all devices are properly grounded. Use the included grounding wire to ground the LCD Console

1213Open/Close ConsoleOpening the ConsoleSlide the 2 Slide Releases toward the center of the LCD Console, then pull the console module out while holdi

Closing the ConsoleFirst, close the LCD module with the handle bar, then pull the safety catches on both sides of the console module towards yourself

PS/2-USB CPUPS/2-USB CPUConsole1415Installation Please make sure the computer is powered off before you start.Step 1Connect the power cord to the powe

orPS/2-USB CPUPS/2-USB CPUConsole*PS/2 KVM Cables (Model No.: G2L5202P, G2L5203P and G2L5206P) are available and sold separately, please visit our web

PS/2-USB CPUPS/2-USB CPUConsole1617Step 3Turn on LCD Console by using the power switch that’s located in the back of the LCD Console. Final StepTurn

PS/2-USB CPUPS/2-USB CPUConsole1617Connect to a KVMNote: This LCD Console is ideal for our GCS1808/GCS1716. Please visit our website at www.iogear.co

1234 5 67811121314 15 161718PS/2-USB CPUCONSOLEPS/2-USB CPUPS/2-USB CPUConsole1819Step 2Connect the provided USB KVM Cable from the CPU port of the

PS/2-USB CPUPS/2-USB CPUConsoleStep 3Refer to your KVM’s manual for details on how to connect your computers to your KVM.Step 4Turn on LCD Console by

23©2009 IOGEAR. All Rights Reserved. Part No. M1122IOGEAR, the IOGEAR logo, MiniView®, VSE are trademarks or registered trademarks of IOGEAR. Microso

PS/2-USB CPUPS/2-USB CPUConsoleVGAPS/2USB2021If you wish to use external monitor, keyboard or mouse rather then the built-in LCD, keyboard or touchpad

2021There is an external mouse port in the front of the LCD Console next to the Power LED. Simply plug in any USB connection of the mouse to that USB

2223There are four buttons for LCD conguration, the functions are as follow:LCD CongurationButton FunctionMenu If you are currently not in the LCD O

2223There are ten functions in the LCD OSD Menu, and they are as follow:Setting FunctionBrightness This function adjusts the brightness of the LCDCont

RESETRESET2425Use a paper clip or any kind of small object to press the reset button, you will then hear a beep sound which indicates that it will per

2425Keyboard Function KeysThere are 6 sets of Keyboard Function Keys on the built-in keyboard and they are as follow. Simply press and hold the [Fn] k

2627Hotkey Commands*This function can ONLY be used if you have physically connected one computer to the LCD Console. If you have connected multiple co

2627Mac Keyboard EmulationThe PC compatible (101/104 key) keyboard can emulate the functions of the Mac keyboard. The emulation mappings are listed in

2829Sun Keyboard EmulationThe PC compatible (101/104 key) keyboard can emulate the functions of the Sun keyboard. The emulation mappings are listed in

2829Firmware UpgradeNote: In order to perform a rmware upgrade, you need to use a set of computer that is not con-nected to the LCD Console.Step 1Con

23Table of ContentsPackage Contents 4System Requirements 5Overview 6Rack Mounting 8Grounding 11Open/Close Console 12Installation 14Connect to

3031Step 6Read the License Agreement and click “I Agree” then click “Next” if you wish to continue with the rmware upgrade. Otherwise, click “Cancel”

Note: If you did not check the “Check Firmware Version” checkbox, utility will perform the upgrade automatically no matter what version of rmware you

Step 10When the rmware upgrade is done, you will see “Firmware upgrade OK” in the “Status Messages” window. Then simply click “Finish” to complete th

F/W UPGRADENORMAL RECOVERF/W UPGRADENORMAL RECOVER3233Upgrade FailIf you don’t see “Firmware upgrade OK” in the “Status Messages” window, it means the

3435GeneralPlease read all of these instructions and save them for future reference.• Carefully follow all warning and instructions marked on the devi

3435In order to prevent damage once installed, it is important that this device and all devices connected to • it are properly grounded.As a safety fe

3637If the following conditions occur, unplug the device from the wall outlet and bring it to qualied • service personnel for repair: - The power co

3637Rack MountingBefore working on the rack, make sure that the stabilizers are secured to the rack, extended to the • oor, and that the full weight

3839SpecicationsModel GCL1800Power Consumption 29.6WPhysical PropertiesHousing Metal + PlasticWeight 25.94lbDimension (W x H x D) 17in. x 1.75in. x

3839Federal Communications Commission (FCC) StatementThis product has been tested and found to comply with the limits for a Class A digital device, pu

45Package Contents- 1 x 17" LCD Console- 1 x USB KVM Cable - 1 x Firmware Upgrade Cable- 1 x Rack Mount Kit (Long and Short L Brackets)- 1 x Grou

4041This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member st

4041SJ/T 11364-2006The following contains information that relates to China.部件名称有毒有害物质或元素铅 (Pb) 汞 (Hg) 镉（Cd） 六价 (Cr(VI))多溴联苯（PBB）多溴二苯醚（PBDE）电器部件 ● ○ ○

4243IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE

4243IOGEAR19641 Da VinciIrvine, CA 92610P 949.453.8782F 949.453.8785Visit us at: www.iogear.com Contact

44© 2009 IOGEAR®FUNIOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high technolo

45System RequirementsComputersVGA, SVGA, or MultiSync video graphics card with an HDB-15 port • PS/2 mouse and keyboard ports (6-pin mini DIN) or 1 US

1245678910111213367OverviewSlide Release1. Handle Bar2. LCD Display3. LCD Power Button4. LCD Controls5. Keyboard6. Touchpad7. External USB Mouse Port8

PS/2-USB CPUPS/2-USB CPUConsole1254768 9367Back viewGrounding Terminal1. Power Socket2. Power Switch3. External USB Mouse Port4. External USB Keyboard

The following diagram shows the required components to mount the LCD Console to the rack.Note: The Slide Mounting Brackets are pre-installed onto the

Step 1While one person holding the LCD Console in the proper position in the rack, the second person can lock the screws loosely through the front bra