Iogear GWU523 Bedienungsanleitung

®Wireless-G USB 2.0 AdapterUser Manual (GWU523)

7InstallationCONNECTING YOUR WLAN USB ADAPTER TO PCNote: Once you insert the installation anddriver CD, it will automatically activate theAutorun ins

InstallationSTEP 2Click Next to continue.8

9InstallationStep 3 :Click Next to install at the designatedfolder. Or, click “Browse”to select different folder.

InstallationStep 4 :Start copying files until it finishthe installation.10

11InstallationStep 5 :Click Finish to complete installation.

InstallationStep 6 :After finished install driver and utility on your system,Windows XP/2000Plug the USB adapter into the USB port of your PC. It will

13InstallationIf the icon in the System Tray is in red,it means that Wireless USB Adapterconfiguration is invalid or incomplete.Double click on that i

InstallationThe Link Quality and Signal Strength bar chart is only active when the node is in InfrastructureMode. The bar graph displays the quality a

15General Connection SettingIn this panel, you can modify the general networkconnection setting, enable/disable the WEP, load /modify profile and othe

When settings are input, click “Apply” toconfirm changes of them.General Connection Setting16

©2005 IOGEAR. All Rights Reserved. PKG-M0146IOGEAR, the IOGEAR logo, MiniView, VSE are trademarks or registered trademarks of IOGEAR, Inc. Microsof

17WEP Encryption Key SettingYou may want an additional measure ofsecurity on your wireless network, which canbe achieved by using WEP (Wired Equivalen

The default state in Encryption Setting is WEPdisabled. Check “Enable WEP” to enable theencryption.For more WEP key setting, Click “WEPEncryption Key

19Click the “x” at the upper right hand corner toreturn to Configuration Tool.WPA Encrytion SettingWPA (Wi-Fi Protected Access) is a securitytechnolog

WPA Encrytion SettingWPA Pre-Shared Key (WPA-PSK) is asimplified but still powerful form of WPA mostsuitable for home Wi-Fi networking. To useWPA-PSK,

21ProfileEach profile represents specific settings of theUSB adapter. You can set the settings for eachprofile. Next time when you want to change theU

Advanced SettingAdvanced Setting Click “Advanced Setting” to select powerconsumption setting that has 3 different modes.In this panel, you can select

23System Information Click “Information” and the pop-up windowwill show the Driver Version,Utility Version, MAC address of this USBadapter and so on.S

WIRELESS LAN BASICSWireless LAN network defined by IEEE802.11b/g standard committee could beconfigured as :1. Ad Hoc wireless LAN, or2. Infrastructure

25Wirelss LAN BasicsInternetAD-HOCComputer to computerNo Access points requiredINFRASTRUCTUREAccess to InternetAccess points required12

IP ADDRESSTo use the Wireless-G USB 2.0 Adapter with acomputing device, your computer must beequipped with an USB 1.1 or 2.0 availableports. All drive

WelcomeThank you for choosing IOGEAR® to serve your wireless needs. In no time you will be sharing filesor surfing the Internet wirelessly. We hope yo

27In network with static IP addressing, the networkadministrator manually assigns an IP address toeach computer. Once a static IP address isassigned,

SpecificationWireless-G USB 2.0 AdapterIEEE 802.11b/g2.400 GHz~ 2.4835 GHz unlicensed ISM band802.11b: QPSK/BPSK/CCK802.11g: OFDM54/48/36/24/18/12/11/

29Wireless-G USB 2.0 AdapterUSB 2.0/1.1Link/ActiveWindows 98SE/ME/2000/XPWindows-based configuration utility and status monitoringFCC for North Americ

TroubleshootingSymptom :The LED is off.Remedy :Make sure the PC Card is inserted properly. Otherwise contact your vendor.Symptom :The LED is always on

31Symptom :The PC Card is linking, but can’t share files with others.Remedy :Make sure the file and printer sharing function is enabled. You can enabl

GLOSSARYIEEE 802.11 StandardThe IEEE 802.11 Wireless LAN standards subcommittee, which is formulating a standard for the industry.Access PointAn inter

Glossary33Direct Sequence Spread SpectrumThis is the method the wireless cards use to transmit data over the frequency spectrum. The other method isfr

IEEEInstitute of Electrical and Electronics Engineers Infrastructure An integrated wireless and wired LAN is called anInfrastructure configuration. In

Glossary35ProtocolA protocol is a standardized set of rules that specify how a conversation is to take place, including the format,timing, sequencing

Temporal Key Integrity Protocol (TKIP)The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE 802.11i encryption standard forwire

Table of contentsPackage ContentsProduct OverviewFeaturesSystem RequirementsIntroductionInstallationGeneral Connection SettingWEP Encryption SettingWP

37Wi-Fi Protected Access (WPA)The Wi-Fi Alliance put together WPA as a data encryption method for 802.11 wireless LANs. WPA is an industry-supported,

Technical SupportIf you need technical support, please check out our IOGEAR Tech Info Library (T.I.L.) atwww.iogear.com/support for the latest tips, t

39Radio & TV Interference StatementWARNING!!! This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used

Limited WarrantyIN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT, SPECIAL,INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE U

23 Hubble • Irvine, CA 92618 • (P) 949.453.8782 • (F) 949.453.8785 • www.iogear.comContact info.®

Package ContentsThis package contains...1 x 802.11g USB 2.0 Adapter1 x Quick Start Guide1 x Installation & Manual CD-ROM1 x Warranty/Registration

OverviewBeing five times faster than the speed of 802.11b network standard devices, the innovative802.11g standard lets the wireless network become in

Features• Support Microsoft Windows 98SE, Me, 2000 and XP.• Operating distance of up to 300 meters in free space.• 54 Mbps Data Rate.• Support USB 1.1

5Pictorial IntroductionLED• LED turns on when POWER is applied to the IOGEAR Wireless-G USB 2.0 Adapter.• LED is blinking when PC is sending data thro

System Requirements- Windows 98SE, ME, 2000 or XP- available USB 1.1. or 2.0 port.6