1GIC704SR5W6PART NO. M0560InstallationInstallationInstallation GuideRAID5 eSATA 1.5Gbps 4 External port PCI Card
10Just a Bunch of Disks (JBOD/Contiguous)JBOD (also known as Contiguous) means a logical drive that can either be an entire disk drive or a segment of
111. Power down the computer system.2. Insert the Host card into an available bus slot.3. Power on the computer system.4. Install drivers for
1211. Use the SATARAID5 Manager GUI to confi gure your RAID settings. If using 1 Disk, please select “Concatenate” or “Contiguous” settings only.
13BIOS (RAID Settings)Creating and deleting RAID sets is a function found in the BIOS. During boot up, the RAID setting message will appear and pause
14Creating Mirrored Sets (RAID 1)1. As the BIOS boots, Press CTRL+S or F4 to enter the RAID bios utility.2. Select Create RAID set. Press Enter.3.
15Creating a Mirrored-Striped Set (RAID 10)1. As the BIOS boots, press CTRL+S or F4 to enter the RAID bios utility.2. Select Create RAID set. Press
16Creating JBOD Sets 1. As the BIOS boots, Press CTRL+S or F4 to enter the RAID bios utility.2. Select Create RAID set. Press Enter.3. Select JBOD
17Deleting RAID Sets1. As the BIOS boots, Press CTRL+S or F4 to enter the RAID bios utility.2. Select Delete RAID set. Press Enter.3. Answer Y to r
18Windows XP Fresh Installation1. Power off the system. Insert the controller card into a PCI slot and connect the hard drives to the controller card.
19Windows XP Existing Installation1. Power off the system. Insert the controller card into a PCI slot and connect the hard drives to the control-ler c
204. Insert the Driver CD in your CD-ROM/DVD drive, check Specify a location, uncheck the other boxes, click Next, type in your CD-ROM/DVD Drive Lette
21Verifying controller installation1. Right click on the ‘My Computer’ icon and select ‘Properties’. Left click on the ‘Hardware’ tab then select the
22Federal Communications Commission (FCC) StatementFederal Communications Commission (FCC) Statement15.21You are cautioned that changes or modifi catio
23- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced
24This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member stat
25The manufacturer, IOGEAR, makes NO warranty or representation, whether express or implied, regarding the contents, use or suitability of this softwa
26ContactToll Free: (866) 9-IOGEARPhone: (949) 453-878223 HubbleIrvine, CA 92618 [email protected]©2007 IOGEAR. All Rights Reserved.
27
© 2007 IOGEAR, INC.FUNIOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high techn
3Table of ContentsCaution 4Introduction 5Features 6Package Contents 7What Is RAID? 8Installation Procedure 11Software Installation 18Federal Communi
4Caution• Before installation of the controller card, we recommend that users study this manual fi rst. This RAID manual has more information on RAID
5IntroductionThe board offers the ability to upgrade your desktop computer to RAID 5, RAID 0+1, RAID 0, or RAID 1 as well as JBOD. The board can contr
6FeaturesPCI InterfaceCompliant with PCI Specifi cations, Revision 2.2.• Integrated PCI DMA engines.• 32 bit, 33/66MHz fully compliant PCI host interfa
7Package ContentsRAID5 SATA-150 4Ports PCI Host Adapter• Quick Start Guide• Driver CD•
8RAID - Redundant Array of Independent DisksRAID technology manages multiple disk drives to enhance I/O performance and provide redundancy in order to
9Mirrored-Striping (RAID 0+1 also known as RAID 10) A Mirrored-Striping Set does just what it says, combining both Striping and Mirroring technologies
Kommentare zu diesen Handbüchern