Iogear Wireless USB Print Server GPSR01U Bedienungsanleitung

Wireless USB Print Server 1 PortUser Manual (GPSR01U)®

Product OverviewExternal print servers enhance capability by letting you place your printers, plotters, or equality printers atconvenient locations di

Reset ButtonLED IndicatorOperation Mode(Normal/DIAG)Power(3.3V 2A)Pictorial Introduction:Reset Button – Recessed button resets the unit.LED Indicator

InstallationBefore you start, you should prepare:• One Windows® 98/Me/2000/XP PC with CD-ROM• One 802.11b Access point and Wireless Adapter• One USB p

Note: For some specific printers you may need to connect the pritner to thecomputer and install the driver first and then connect it to the print serv

The Wizard will search for the print server on yournetwork. If the print server does not show up, clickthe [Refresh] button.Note: If you’re Print Ser

This window allows you to configure the printserver. Select “Yes, I want to change settings” andclick Next. By default, there is no password.6.12Insta

Basic Wireless Settings - In this window you canchange the Communication Type, SSID andData Transmission rates.Change the SSID to match your wirelessn

14InstallationTCP/IP Settings – In this window you canconfigure the Wireless Print Server to obtain an IPaddress automatically from your DHCP server,

15InstallationInstallation complete. Click Finish to close thewizard.11.NOTE: If you had to change the SSID of the print server to matchyour network S

16InstallationChange the SSID of you network card back to theSSID used on your network and change theNetwork Type back to Infrastructure.12. 13. Now s

The wizard will now search for print servers onthe network.17Installation15.14. Before we proceed, make sure your printserver and printer are on. Once

Once the server finds the print server, highlightit and click Next.18Installation16. 17. Since we have already set-up the print server inthe previous

19Installation18. The wizard will help you set up the printer that isconnected to the print server. Select “Add NewPrinter” . If your driver is alre

21. Select Local Printer. Click Next.Make sure auto detect is not checked.20Installation20. The next window is the Add Printer wizard. ClickNext.

21Installation23. Click on the TCP/IP tab. The wizard will nowsearch for your print server. Highlight your printserver and click OK. If your print ser

22Installation24. Select your printer from the list and click “Next”. 25. The wizard will ask you if you want to keep theexisting driver or use the ne

23Installation27. Indicate whether you want to share this printeron your network and click Next.Note: There should be no reason to share it as the pri

29. Click Finish to complete the Add Printer wizard.24Installation28. On the print test page window, select Yes or Nowhether you want to print a test

25Installation30. Now that you added your printer, it should showup in the list. Highlight your printer and click Next.31. The following window displa

Select “Exit” to complete the installation.33.26Installation32. Installation is complete. Select Finish to completethe wizard.

Thank you for purchasing one of the most feature-rich wireless print servers on the market. IOGEAR®’sWireless USB Print Server’s are first rate connec

27Macintosh InstallationIOGEAR Wireless Print Server Installation in MacOSX1. Open the box the Wireless Print Server came in.Follow the proper include

you may need to reset your Wireless PrintServer. You can do this by unplugging theunit, plugging it back in, and waiting a fewmoments. Repeat steps 2

29Macintosh Installation6. Since the IP address is 192.168.5.1, your networkmay not be on the same subnet as the WirelessPrint Server. You will need t

30Macintosh Installation8. Once you’ve opened the System Preferences,select Network9. When you select Network, you will see thenetwork Status of your

12. Once you select TCP/IP, there is a menu calledConfigure Ipv4: Select Manually31Macintosh Installation10. Select Airport, and then click Configure.

15. The Wireless Print Server’s web-interface willappear. Click on Setup.32Macintosh Installation14. After you click Apply Now, simply open Safari (or

33Macintosh Installation16. Once you select Setup, you will now see theconfiguration menus as you scroll down.17. The first section is for the Print

34Macintosh Installation18. This is the wireless section.Basic Settings – Here you will configure theMode, SSID, Channel, and Data Transmissionrates o

35Macintosh Installation19. The next section is for setting up your Print Serverin a Novell environment. These settings must betailored to how your No

36Macintosh Installationaddress on the Print Server 192.168.1.254, or192.168.1.253, etc. It will not matter what the lastseries of numbers are (x.x.x.

Table of ContentsPackage Contents...

23. You may now Save your settings.37Macintosh Installation22. AppleTalk Settings You may leave these asdefault.24. Once you have clicked Save, your P

25. During this time, you may change your NetworkSettings back to what you had them set to before.Ex. If you were using DHCP before, you willselect it

30. Click Add.31. In the top pull down box, select IP Printing.NOTE: You can select AppleTalk as well. It will notrequire you to enter an IP address a

Click Add when finished.Please Note: Your Print Server is now installedand should function properly. If you have anydifficulties, please do not hesita

Changing the SSID on the Print ServerTo change the SSID on the Print Server, you mustwirelessly connect to the print server in AD-HOC(Computer-to-Comp

Next right-click on the wireless network connectionand click on properties.In the general tab click on the wireless networkstab.2. 3.Changing SSID on

Take note of the name that is shown for yourwireless router. In the example below is “linksys”,we are going to need that information later.Click on th

6. After it goes back to the “Wireless NetworkConnection Properties.” Click the Add button.7. On the Network name (SSID) enter “WLAN-PS”.Uncheck othe

Changing SSID on Print Server458. Go back to the Wireless Setup Wizard. Click onrefresh. The Print Server will show up this time.9. Bring back the PS

Changing SSID on Print Server4610. Once it is started, the PS Admin application willshow the Print Server on it. Double-click on it tochange its setti

2Un-installation...

Changing SSID on Print Server4712. Change the SSID to match your router SSID.Mentioned on step 4. (Linksys in this example)13. The printer server will

Changing SSID on Print Server4814. Turn the printer server off by unplugging itChange the mode from AD_HOC on the PrinterServer Hardware, by flipping

Changing SSID on Print Server4916. Click on Advance.17. Click on Any available Network, and close.

Changing SSID on Print Server5018. Go back to the “Wireless Setup Wizard.” Click onRefresh. The Print server should show up on it.Once printer server

Changing SSID on Print Server5120. Select Finish.Go back to the initial screen and choose NetworkPrint Server Setup wizard.21. The following screen wi

Changing SSID on Print Server5223. The setting will be shown on the next screen.22. You can choose the printer to use.

Changing SSID on Print Server5324. Click on Finish and proceed to use the newprinter.

IPP OverviewPrint server(s) support the Internet Printing Protocol(IPP). Using the appropriate software on your system,you can create an IPP print pat

Select the appropriate printer manufacturer andprinter type again and click Next.8.In URL’s box, input print server’s IP address, forexample, http://1

If you want your Windows-based programs touse this printer as the default printer, pleaseselect Yes, and click Next.9. Click Finish.10.Internet Printi

Package ContentsThis package contains:1 – Wireless USB Print Server1 – User Manual1 – Installation CD1 – Warranty/Registration card1 – Power Adapter*

Configuration from Embedded Web ServerWeb Based ConfigurationOverviewThe Print Server contains an embedded web serverthat can be accessed through a su

You will be able to view system status, such asDevice Name, System Contact, System Location,System Uptime, and Firmware Version.Printer StatusPrinter

SSID: The Service Set ID. This should be set to thesame value as other wireless devices in yournetwork. (Default: ANY)Channel Number: The radio channe

Use DHCP/BOOTP: This option allows you to viewDHCP/ BOOTP status. If there is a DHCP/BOOTPserver on your network, this option allows the printserver t

Apple TalkApple Talk displays the AppleTalk settings of the printserver.General SettingsAllows you to view NetWare Settings, such as PrintServer Name,

Web Based ConfigurationDevice Name: This option allows you to input devicename of the print server. To correct the print server’sdevice name.System Co

WEP SettingsUse WEP: Enable or Disable encryption.Key Format: Select whether you want the Keyformat to be either alphanumeric or hexadecimal.WEP Key-

TCP IP StatusThis section allows you to configure the TCP/IPsettings of the wireless print server.DHCP/BOOTP: This option allows you to selectDHCP/ BO

NetWare SetupThis section allows you to configure the NetWaresettings of the wireless print server.Web Based ConfigurationPrint Server Name: This opti

Web Based ConfigurationSNMP SetupThis section allows you to configure the SNMPsettings of the print server.Support HP WebJetAdmin: This option allows

4IOGEAR®’s palm sized single-port Wireless USB Print Server allows any networked computer to wirelesslyshare a USB printer. It complies with USB 1.1 s

Web Based ConfigurationZone Name: Type an AppleTalk Zone name that youwant the print server to belong to or leave it in default(This enables the print

1. Click on the Browse button and search for the binary file.2. Once you’ve found the binary file, click theUpgrade button.Load DefaultThis but

Once you select the Load Default button, a windowwill appear. The window will ask you if you want torestore factory default settings. Click OK to res

70Uninstalling the PSAdmin on Windows PCTo help users easily remove all installed softwarecomponents of the PSAdmin from their Windows PC,the PSAdmin

Select the Wireless tab. Enter the ESSID, Channel,Rates that meet your network environment, thenpress OK.715.AppendixAppendix: Diagnostic ModeIf you’v

6. Done! The print server will restart.Flip the DIP switch on the print server back tonormal mode (away from the power connector)and change your wir

73If you are still experiencing problems after reading Product User Manual and the Troubleshooting section,you may either contact our technical suppor

Radio & TV Interference StatementWARNING!!! This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused i

IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OFTHE PRODUCT

• Easily connect your USB printer to a wireless network• Allows multiple computers to share one USB printer on the wireless network• Print from any co

23 Hubble • Irvine, CA 92618 • (P) 949.453.8782 • (F) 949.453.8785 • www.iogear.comContact info.®

System RequirementsOperating Systems:• Windows® 98SE/ME/2000/XP• Novell (iBindery/NDS)• Mac OS 8.6 or Later (supports-enabled Mac only)*• Unix/Linux*